4F1910552H original ECU files
3 original (stock) ECU files with the part number 4F1910552H — Bosch MED9.1, used in Audi vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All 4F1910552H files 3
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| 0261S02482 1037389462 Audi S54.2 354hp | Bosch MED9.1 | 0261S02482 | 1037389462 | 4F1910552H 0010 | €20 · Open |
| 0261S02482 1037393910 Audi S54.2 354hp | Bosch MED9.1 | 0261S02482 | 1037393910 | 4F1910552H 0020 | €20 · Open |
| 0261S02482 1037393910 Audi S65.2 435hp | Bosch MED9.1 | 0261S02482 | 1037393910 | 4F1910552H 0020 | €20 · Open |
No file in this list matches. Search all original files →
About 4F1910552H
4F1910552H is on 3 original (stock) ECU files in our catalogue: as the calibration on 3 files and as the SW upgrade number on 2 files.
They were read from Bosch MED9.1 (3 files) control units.
Our catalogue lists them for the Audi S5 (4.2 354hp) and Audi S6 (5.2 435hp).
Other numbers on these files: 1 hardware number (0261S02482); 2 software numbers (1037393910, 1037389462).
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- 4F1910552H
- Files
- 3
- Found as
- calibration and SW upgrade number
- ECU types
- 1
- Vehicles
- 2
- Also written as
- 4F1 910 552 H
ECU types with 4F1910552H 1
Vehicles with 4F1910552H 2
Tuning for Bosch MED9.1 — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is 4F1910552H listed for?
In our catalogue: Audi S5 (4.2 354hp) and Audi S6 (5.2 435hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has 4F1910552H?
In our catalogue 4F1910552H is on files read from Bosch MED9.1 (3 files) control units.
There are several 4F1910552H files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.