Hardware number · 3 files

H18MRA6 original ECU files

3 original (stock) ECU files with the hardware number H18MRA6 — Denso SH7058, used in Mitsubishi vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.

3files
1ECU types
1models
1makes

All H18MRA6 files 3

VehicleECUHWSWCalibration / upgrade
T1A1HEA1FC01 Mitsubishi Shogun3.2 160hp Denso SH7058 H18MRA6 T1A1HEA1FC01 H18MRA6 T1A1HEA1FC01 1860C11902 €20 · Open
T1A1HEA1FD01 Mitsubishi Shogun3.2 160hpMap pack · 50 maps Denso SH7058 H18MRA6 T1A1HEA1FD01 H18MRA6 T1A1HEA1FD01 1860C12002 €20 · OpenWith maps €60
T1A1HEA1FF01 Mitsubishi Shogun3.2 160hp Denso SH7058 H18MRA6 T1A1HEA1FF01 H18MRA6 T1A1HEA1FF01 1860C12102 €20 · Open

About H18MRA6

H18MRA6 is on 3 original (stock) ECU files in our catalogue, always as the hardware number.

They were read from Denso SH7058 (3 files) control units.

Our catalogue lists them for the Mitsubishi Shogun (3.2 160hp).

Other numbers on these files: 3 software numbers (T1A1HEA1FC01, T1A1HEA1FD01, T1A1HEA1FF01); 3 calibration / SW upgrade numbers (1860C11902, 1860C12002, 1860C12102).

To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.

Number
H18MRA6
Files
3
Found as
hardware number
ECU types
1
Vehicles
1

ECU types with H18MRA6 1

Vehicles with H18MRA6 1

More Denso SH7058 numbers 24

Need a modified file?

Tuning for Denso SH7058 — done by our engineers

  • Stage 1 / Stage 2 / ECO
  • DPF / FAP OFF
  • EGR OFF
  • AdBlue / SCR OFF
  • DTC OFF
  • Speed limiter, Start&Stop

Questions

Which vehicles is H18MRA6 listed for?

In our catalogue: Mitsubishi Shogun (3.2 160hp). Open the file page that matches your vehicle, engine and numbers.

Which ECU has H18MRA6?

In our catalogue H18MRA6 is on files read from Denso SH7058 (3 files) control units.

There are several H18MRA6 files. Which one do I need?

The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.

How do I get the file?

Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.

What exactly do I receive?

The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.