03G906018FC original ECU files
4 original (stock) ECU files with the software number 03G906018FC — Siemens PPD1.2, used in Volkswagen vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All 03G906018FC files 4
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| 03G906018FC 4357 Volkswagen Golf2.0 170hp | Siemens PPD1.2 | — | — | 03G906018FC 4357 | €20 · Open |
| 1155 03G906018FC Volkswagen Golf 52.0 170hp · BMN | Siemens PPD1.2 | 1155 | 03G906018FC | 03G906018FC 1155 | €20 · Open |
| 1879 03G906018FC Volkswagen Golf 52.0 170hp · BMNMap pack · 100 maps | Siemens PPD1.2 | 1879 | 03G906018FC | 03G906018FC 1879 | €20 · OpenWith maps €60 |
| 4357 03G906018FC Volkswagen Golf 52.0 170hpMap pack · 105 maps | Siemens PPD1.2 | 4357 | 03G906018FC | 03G906018FC 4357 | €20 · OpenWith maps €60 |
No file in this list matches. Search all original files →
About 03G906018FC
03G906018FC is on 4 original (stock) ECU files in our catalogue: as the calibration on 4 files, as the SW upgrade number on 4 files and as the software number on 3 files.
They were read from Siemens PPD1.2 (4 files) control units.
Our catalogue lists them for the Volkswagen Golf 5 (2.0 170hp) and Volkswagen Golf (2.0 170hp).
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- 03G906018FC
- Files
- 4
- Found as
- calibration, SW upgrade number and software number
- ECU types
- 1
- Vehicles
- 2
- Also written as
- 03G 906 018 FC
ECU types with 03G906018FC 1
Vehicles with 03G906018FC 2
Tuning for Siemens PPD1.2 — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is 03G906018FC listed for?
In our catalogue: Volkswagen Golf 5 (2.0 170hp) and Volkswagen Golf (2.0 170hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has 03G906018FC?
In our catalogue 03G906018FC is on files read from Siemens PPD1.2 (4 files) control units.
There are several 03G906018FC files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.