T2G1LC10D original ECU files
3 original (stock) ECU files with the software number T2G1LC10D — Denso SH7059, Denso D3, used in Renault Truck, Nissan Truck vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All T2G1LC10D files 3
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| E51ZU4E Nissan Truck Cabstar2.5 130hpMap pack · 88 maps | Denso SH7059 | E51ZU4E | T2G1LC10D | E51ZU4E T2G1LC10D LC14C | €20 · OpenWith maps €90 |
| E51ZU4E Renault Truck Maxity2.5 140hp | Denso D3 | T2G1LC10D | E51ZU4E | — | €20 · Open |
| E51ZU4E Renault Truck Maxity2.5 140hp | Denso SH7059 | E51ZU4E | T2G1LC10D | E51ZU4E T2G1LC10D LC12C | €20 · Open |
No file in this list matches. Search all original files →
About T2G1LC10D
T2G1LC10D is on 3 original (stock) ECU files in our catalogue: as the software number on 2 files and as the hardware number on 1 file.
They were read from Denso SH7059 (2 files) and Denso D3 (1 file) control units.
Our catalogue lists them for the Renault Truck Maxity (2.5 140hp) and Nissan Truck Cabstar (2.5 130hp).
Other numbers on these files: 1 hardware number (E51ZU4E), listed on 2 of the 3 files; 1 software number (E51ZU4E), listed on 1 of the 3 files.
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- T2G1LC10D
- Files
- 3
- Found as
- software number and hardware number
- ECU types
- 2
- Vehicles
- 2
ECU types with T2G1LC10D 2
Vehicles with T2G1LC10D 2
Tuning for T2G1LC10D — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is T2G1LC10D listed for?
In our catalogue: Renault Truck Maxity (2.5 140hp) and Nissan Truck Cabstar (2.5 130hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has T2G1LC10D?
In our catalogue T2G1LC10D is on files read from Denso SH7059 (2 files) and Denso D3 (1 file) control units.
There are several T2G1LC10D files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.