Software number · 2 files

T1D0HED0J501 original ECU files

2 original (stock) ECU files with the software number T1D0HED0J501 — Denso RA6, Denso SH7058, used in Mitsubishi vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.

2files
2ECU types
2models
1makes

All T1D0HED0J501 files 2

VehicleECUHWSWCalibration / upgrade
1860C18804 Mitsubishi L2002.5 176hp · 4D56IT3Map pack · 49 maps Denso RA6 1860C18804 T1D0HED0J501 H19ERA6 €20 · OpenWith maps €60
H19ERA6 Mitsubishi Pajero3.2 200hp Denso SH7058 H19ERA6 T1D0HED0J501 H19ERA6 T1D0HED0J501 1860C18804 €20 · Open

About T1D0HED0J501

T1D0HED0J501 is on 2 original (stock) ECU files in our catalogue, always as the software number.

They were read from Denso RA6 (1 file) and Denso SH7058 (1 file) control units.

Our catalogue lists them for the Mitsubishi L200 (2.5 176hp) and Mitsubishi Pajero (3.2 200hp).

Other numbers on these files: 2 hardware numbers (1860C18804, H19ERA6); 2 calibration / SW upgrade numbers (H19ERA6, 1860C18804).

To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.

Number
T1D0HED0J501
Files
2
Found as
software number
ECU types
2
Vehicles
2

ECU types with T1D0HED0J501 2

Vehicles with T1D0HED0J501 2

More Denso RA6 numbers 21

Need a modified file?

Tuning for T1D0HED0J501 — done by our engineers

  • Stage 1 / Stage 2 / ECO
  • DPF / FAP OFF
  • EGR OFF
  • AdBlue / SCR OFF
  • DTC OFF
  • Speed limiter, Start&Stop

Questions

Which vehicles is T1D0HED0J501 listed for?

In our catalogue: Mitsubishi L200 (2.5 176hp) and Mitsubishi Pajero (3.2 200hp). Open the file page that matches your vehicle, engine and numbers.

Which ECU has T1D0HED0J501?

In our catalogue T1D0HED0J501 is on files read from Denso RA6 (1 file) and Denso SH7058 (1 file) control units.

There are several T1D0HED0J501 files. Which one do I need?

The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.

How do I get the file?

Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.

What exactly do I receive?

The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.