Software number · 4 files

S180037040Z9 original ECU files

4 original (stock) ECU files with the software number S180037040Z9 — Siemens VDO, Siemens M3C, used in Kymco, Competition, TGB vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.

4files
2ECU types
4models
3makes

All S180037040Z9 files 4

VehicleECUHWSWCalibration / upgrade
4UF12MPV6CT306431 Competition Siemens0hp Siemens VDO 4UF12MPV6CT306431 S180037040Z9 — €20 · Open
2008343172 Kymco Maxxer450 30hp Siemens VDO 2008343172 S180037040Z9 — €20 · Open
2018178887 Kymco UXV0.7 20hp Siemens VDO 2018178887 S180037040Z9 — €20 · Open
QB031I31 TGB Blade500 40hp Siemens M3C S180037040Z9 QB031I31 QB031I31 €20 · Open

About S180037040Z9

S180037040Z9 is on 4 original (stock) ECU files in our catalogue: as the software number on 3 files and as the hardware number on 1 file.

They were read from Siemens VDO (3 files) and Siemens M3C (1 file) control units.

Our catalogue lists them for the Competition Siemens, Kymco Maxxer (450 30hp), Kymco UXV (0.7 20hp) and TGB Blade (500 40hp).

Other numbers on these files: 3 hardware numbers (4UF12MPV6CT306431, 2008343172, 2018178887), listed on 3 of the 4 files; 1 software number (QB031I31), listed on 1 of the 4 files.

To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.

Number
S180037040Z9
Files
4
Found as
software number and hardware number
ECU types
2
Vehicles
4

ECU types with S180037040Z9 2

Vehicles with S180037040Z9 4

Need a modified file?

Tuning for S180037040Z9 — done by our engineers

  • Stage 1 / Stage 2 / ECO
  • DPF / FAP OFF
  • EGR OFF
  • AdBlue / SCR OFF
  • DTC OFF
  • Speed limiter, Start&Stop

Questions

Which vehicles is S180037040Z9 listed for?

In our catalogue: Competition Siemens, Kymco Maxxer (450 30hp), Kymco UXV (0.7 20hp) and TGB Blade (500 40hp). Open the file page that matches your vehicle, engine and numbers.

Which ECU has S180037040Z9?

In our catalogue S180037040Z9 is on files read from Siemens VDO (3 files) and Siemens M3C (1 file) control units.

There are several S180037040Z9 files. Which one do I need?

The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.

How do I get the file?

Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.

What exactly do I receive?

The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.