TGB Blade original ECU files
18 original (stock) ECU files for the TGB Blade: 1 ECU type and 3 engine versions. Find your exact file by its hardware (HW), software (SW) or calibration number and compare it with your own read.
ECU types in the TGB Blade 1
Engine versions 3
All TGB Blade files 18
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| TGB Blade1.0 82hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade1.0 82hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade1.0 82hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade1.0 82hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade1.0 82hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade500 40hp | Siemens M3C | — | — | — | €20 · Open |
| S180037040Z9 QB031I31 TGB Blade500 40hp | Siemens M3C | S180037040Z9 | QB031I31 | QB031I31 | €20 · Open |
| TGB Blade500 40hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade500 40hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade500 40hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade500 40hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade500 40hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade500 40hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade500 40hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade500 40hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade0.6 44hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade0.6 44hp | Siemens M3C | — | — | — | €20 · Open |
| TGB Blade0.6 44hp | Siemens M3C | — | — | — | €20 · Open |
All hardware, software and calibration numbers
Find the number from your ECU read (Ctrl+F) and open the matching file.
Hardware (HW) · 1
Software (SW) · 1
Calibration / SW upgrade · 1
Tuning for TGB Blade — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Are these files modified?
No. Every file is an original (stock) read of a TGB Blade control unit, delivered exactly as read. If you need a modified file, order tuning below.
How do I find the right file?
Read the ECU with your tool and compare the hardware (HW) and software (SW) numbers — and the calibration when several files share one software number. The vehicle name alone is not enough: the identifiers decide.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.
My number is not listed. What now?
Then we do not have this file: every original file we have is listed on this site and found by its search, so we cannot get it for you. Search one number at a time — HW, SW or calibration — exactly as it appears in your read.
Can you tune TGB Blade?
Yes. We make Stage 1/2 files and DPF, EGR, AdBlue/SCR and DTC solutions for TGB Blade (depending on the engine). Upload your read on our file service.