GG06R2BGT16A original ECU files
6 original (stock) ECU files with the hardware number GG06R2BGT16A — Denso RF8B, used in Mazda vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All GG06R2BGT16A files 6
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| Mazda 62.2 16V 163hp | Denso RF8B | GG06R2BGT16A | — | — | €20 · Open |
| Mazda 62.2 16V 163hp | Denso RF8B | GG06R2BGT16A | — | — | €20 · Open |
| Mazda 62.2 16V 163hp | Denso RF8B | GG06R2BGT16A | — | — | €20 · Open |
| Mazda 62.2 16V 163hpMap pack · 53 maps | Denso RF8B | GG06R2BGT16A | — | — | €20 · OpenWith maps €60 |
| Mazda 62.2 16V 163hp | Denso RF8B | GG06R2BGT16A | — | — | €20 · Open |
| Mazda 62.2 16V 163hp | Denso RF8B | GG06R2BGT16A | — | — | €20 · Open |
No file in this list matches. Search all original files →
About GG06R2BGT16A
GG06R2BGT16A is on 6 original (stock) ECU files in our catalogue, always as the hardware number.
They were read from Denso RF8B (6 files) control units.
Our catalogue lists them for the Mazda 6 (2.2 16V 163hp).
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy. 6 of these files have the same numbers, ECU, vehicle and engine as another file in this list.
- Number
- GG06R2BGT16A
- Files
- 6
- Found as
- hardware number
- ECU types
- 1
- Vehicles
- 1
ECU types with GG06R2BGT16A 1
Vehicles with GG06R2BGT16A 1
Tuning for Denso RF8B — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is GG06R2BGT16A listed for?
In our catalogue: Mazda 6 (2.2 16V 163hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has GG06R2BGT16A?
In our catalogue GG06R2BGT16A is on files read from Denso RF8B (6 files) control units.
There are several GG06R2BGT16A files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.