G40LRF7JT3LA original ECU files
7 original (stock) ECU files with the hardware number G40LRF7JT3LA — Denso RF8B, used in Mazda vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All G40LRF7JT3LA files 7
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| Mazda 62.0 120hp | Denso RF8B | G40LRF7JT3LA | — | — | €20 · Open |
| Mazda 62.0 120hp | Denso RF8B | G40LRF7JT3LA | — | — | €20 · Open |
| Mazda 62.0 120hp | Denso RF8B | G40LRF7JT3LA | — | — | €20 · Open |
| Mazda 62.0 120hp | Denso RF8B | G40LRF7JT3LA | — | — | €20 · Open |
| Mazda 62.0 120hpMap pack · 28 maps | Denso RF8B | G40LRF7JT3LA | — | — | €20 · OpenWith maps €60 |
| Mazda 62.0 120hpMap pack · 28 maps | Denso RF8B | G40LRF7JT3LA | — | — | €20 · OpenWith maps €60 |
| Mazda CX-72.0 173hpMap pack · 11 maps | Denso RF8B | G40LRF7JT3LA | — | — | €20 · OpenWith maps €60 |
No file in this list matches. Search all original files →
About G40LRF7JT3LA
G40LRF7JT3LA is on 7 original (stock) ECU files in our catalogue, always as the hardware number.
They were read from Denso RF8B (7 files) control units.
Our catalogue lists them for the Mazda 6 (2.0 120hp) and Mazda CX-7 (2.0 173hp).
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy. 6 of these files have the same numbers, ECU, vehicle and engine as another file in this list.
- Number
- G40LRF7JT3LA
- Files
- 7
- Found as
- hardware number
- ECU types
- 1
- Vehicles
- 2
ECU types with G40LRF7JT3LA 1
Vehicles with G40LRF7JT3LA 2
Tuning for Denso RF8B — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is G40LRF7JT3LA listed for?
In our catalogue: Mazda 6 (2.0 120hp) and Mazda CX-7 (2.0 173hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has G40LRF7JT3LA?
In our catalogue G40LRF7JT3LA is on files read from Denso RF8B (7 files) control units.
There are several G40LRF7JT3LA files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.