8E0909518AS original ECU files
3 original (stock) ECU files with the part number 8E0909518AS — Bosch ME7.5, used in Audi vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All 8E0909518AS files 3
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| 0261208500 1037369011 Audi A41.8 190hp | Bosch ME7.5 | 0261208500 | 1037369011 | 8E0909518AS 0003 | €20 · Open |
| 0261208500 0003 Audi A41.8 20V 163hp | Bosch ME7.5 | 0261208500 | — | 8E0909518AS 0003 | €20 · Open |
| 0261208500 1037369011 Audi A41.8 20V 163hp | Bosch ME7.5 | 0261208500 | 1037369011 | 8E0909518AS 0003 | €20 · Open |
No file in this list matches. Search all original files →
About 8E0909518AS
8E0909518AS is on 3 original (stock) ECU files in our catalogue: as the calibration on 3 files and as the SW upgrade number on 2 files.
They were read from Bosch ME7.5 (3 files) control units.
Our catalogue lists them for the Audi A4 (1.8 20V 163hp, 1.8 190hp).
Other numbers on these files: 1 hardware number (0261208500); 1 software number (1037369011), listed on 2 of the 3 files.
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- 8E0909518AS
- Files
- 3
- Found as
- calibration and SW upgrade number
- ECU types
- 1
- Vehicles
- 1
- Also written as
- 8E0 909 518 AS
ECU types with 8E0909518AS 1
Vehicles with 8E0909518AS 1
Tuning for Bosch ME7.5 — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is 8E0909518AS listed for?
In our catalogue: Audi A4 (1.8 20V 163hp, 1.8 190hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has 8E0909518AS?
In our catalogue 8E0909518AS is on files read from Bosch ME7.5 (3 files) control units.
There are several 8E0909518AS files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.