SH1M-18881-T original ECU files
3 original (stock) ECU files with the hardware number SH1M-18881-T — Denso SH725X, Denso SHT5, Denso SH3G, used in Mazda vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All SH1M-18881-T files 3
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| SH1M-188K2-T Mazda CX-52.2 175hp | Denso SH725X | — | SH1M-18881-T | SH1M-18881-T SH1M-188K2-T | €20 · Open |
| SH1M-188K2-T Mazda CX-52.2 175hp | Denso SHT5 | SH1M-18881-T | SH1M-188K2-T | — | €20 · Open |
| SH1M-188K2-T Mazda CX-52.2 175hp | Denso SH3G | SH1M-18881-T | SH1M-188K2-T | — | €20 · Open |
No file in this list matches. Search all original files →
About SH1M-18881-T
SH1M-18881-T is on 3 original (stock) ECU files in our catalogue: as the hardware number on 2 files, as the software number on 1 file and as the calibration on 1 file.
They were read from Denso SH725X (1 file), Denso SHT5 (1 file) and Denso SH3G (1 file) control units.
Our catalogue lists them for the Mazda CX-5 (2.2 175hp).
Other numbers on these files: 1 software number (SH1M-188K2-T), listed on 2 of the 3 files; 1 calibration / SW upgrade number (SH1M-188K2-T), listed on 1 of the 3 files.
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- SH1M-18881-T
- Files
- 3
- Found as
- hardware number, software number and calibration
- ECU types
- 3
- Vehicles
- 1
- Also written as
- SH1M18881T · SH1M 18881 T
ECU types with SH1M-18881-T 3
Vehicles with SH1M-18881-T 1
Tuning for SH1M-18881-T — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is SH1M-18881-T listed for?
In our catalogue: Mazda CX-5 (2.2 175hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has SH1M-18881-T?
In our catalogue SH1M-18881-T is on files read from Denso SH725X (1 file), Denso SHT5 (1 file) and Denso SH3G (1 file) control units.
There are several SH1M-18881-T files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.