SH07-188K2-L original ECU files
3 original (stock) ECU files with the software number SH07-188K2-L — Denso SH1, Denso SH06, used in Mazda vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All SH07-188K2-L files 3
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| SH07-18881-L Mazda 62.2 Skyactiv-D 175hp | Denso SH06 | SH07-18881-L | SH07-188K2-L | — | €20 · Open |
| SH07-18881-L Mazda 62.2 Skyactiv-D 175hp | Denso SH1 | SH07-18881-L | SH07-188K2-L | — | €20 · Open |
| SH07-18881-G Mazda Atenza2.2 Skyactiv-D 175hp | Denso SH1 | SH07-18881-G | SH07-188K2-L | — | €20 · Open |
No file in this list matches. Search all original files →
About SH07-188K2-L
SH07-188K2-L is on 3 original (stock) ECU files in our catalogue, always as the software number.
They were read from Denso SH1 (2 files) and Denso SH06 (1 file) control units.
Our catalogue lists them for the Mazda 6 (2.2 Skyactiv-D 175hp) and Mazda Atenza (2.2 Skyactiv-D 175hp).
Other numbers on these files: 2 hardware numbers (SH07-18881-L, SH07-18881-G).
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- SH07-188K2-L
- Files
- 3
- Found as
- software number
- ECU types
- 2
- Vehicles
- 2
- Also written as
- SH07188K2L · SH07 188K2 L
ECU types with SH07-188K2-L 2
Vehicles with SH07-188K2-L 2
Tuning for SH07-188K2-L — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is SH07-188K2-L listed for?
In our catalogue: Mazda 6 (2.2 Skyactiv-D 175hp) and Mazda Atenza (2.2 Skyactiv-D 175hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has SH07-188K2-L?
In our catalogue SH07-188K2-L is on files read from Denso SH1 (2 files) and Denso SH06 (1 file) control units.
There are several SH07-188K2-L files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.