SH01-188K1-A original ECU files
3 original (stock) ECU files with the hardware number SH01-188K1-A — Denso SH1, used in Mazda vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All SH01-188K1-A files 3
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| SH02-188K2-M Mazda CX-52.2 Skyactiv-D 150hp | Denso SH1 | SH01-188K1-A | SH02-188K2-M | — | €20 · Open |
| SH03-18881-N Mazda CX-52.2 Skyactiv-D 150hp | Denso SH1 | SH01-188K1-A | SH03-18881-N | — | €20 · Open |
| SH3P-18881-D Mazda CX-52.2 Skyactiv-D 175hp | Denso SH1 | SH3P-18881-D | SH01-188K1-A | — | €20 · Open |
No file in this list matches. Search all original files →
About SH01-188K1-A
SH01-188K1-A is on 3 original (stock) ECU files in our catalogue: as the hardware number on 2 files and as the software number on 1 file.
They were read from Denso SH1 (3 files) control units.
Our catalogue lists them for the Mazda CX-5 (2.2 Skyactiv-D 150hp, 2.2 Skyactiv-D 175hp).
Other numbers on these files: 1 hardware number (SH3P-18881-D), listed on 1 of the 3 files; 2 software numbers (SH02-188K2-M, SH03-18881-N), listed on 2 of the 3 files.
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- SH01-188K1-A
- Files
- 3
- Found as
- hardware number and software number
- ECU types
- 1
- Vehicles
- 1
- Also written as
- SH01188K1A · SH01 188K1 A
ECU types with SH01-188K1-A 1
Vehicles with SH01-188K1-A 1
Tuning for Denso SH1 — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is SH01-188K1-A listed for?
In our catalogue: Mazda CX-5 (2.2 Skyactiv-D 150hp, 2.2 Skyactiv-D 175hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has SH01-188K1-A?
In our catalogue SH01-188K1-A is on files read from Denso SH1 (3 files) control units.
There are several SH01-188K1-A files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.