R2AA-188K1-B original ECU files
3 original (stock) ECU files with the hardware number R2AA-188K1-B — Denso R2AB, used in Mazda vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All R2AA-188K1-B files 3
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| R2AJ-18881-D Mazda 32.2 150hp · R2 | Denso R2AB | R2AA-188K1-B | R2AJ-18881-D | R2AJ-188K2-D | €20 · Open |
| R2AA-18881-J Mazda 62.2 125hp · R2Map pack · 55 maps | Denso R2AB | R2AA-188K1-B | R2AA-18881-J | — | €20 · OpenWith maps €60 |
| R2AB-18881-J Mazda 62.2 163hp · R2 | Denso R2AB | R2AA-188K1-B | R2AB-18881-J | — | €20 · Open |
No file in this list matches. Search all original files →
About R2AA-188K1-B
R2AA-188K1-B is on 3 original (stock) ECU files in our catalogue, always as the hardware number.
They were read from Denso R2AB (3 files) control units.
Our catalogue lists them for the Mazda 6 (2.2 125hp, 2.2 163hp) and Mazda 3 (2.2 150hp).
Other numbers on these files: 3 software numbers (R2AJ-18881-D, R2AA-18881-J, R2AB-18881-J); 1 calibration / SW upgrade number (R2AJ-188K2-D), listed on 1 of the 3 files.
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- R2AA-188K1-B
- Files
- 3
- Found as
- hardware number
- ECU types
- 1
- Vehicles
- 2
- Also written as
- R2AA188K1B · R2AA 188K1 B
ECU types with R2AA-188K1-B 1
Vehicles with R2AA-188K1-B 2
Tuning for Denso R2AB — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is R2AA-188K1-B listed for?
In our catalogue: Mazda 6 (2.2 125hp, 2.2 163hp) and Mazda 3 (2.2 150hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has R2AA-188K1-B?
In our catalogue R2AA-188K1-B is on files read from Denso R2AB (3 files) control units.
There are several R2AA-188K1-B files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.