NZ6A-14C204-VA original ECU files
2 original (stock) ECU files with the calibration NZ6A-14C204-VA — Bosch MG1CS017, used in Ford vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All NZ6A-14C204-VA files 2
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| M1PA-12B684-AA M1PA-12A650-DA Ford Bronco2.0 240hp | Bosch MG1CS017 | M1PA-12B684-AA | M1PA-12A650-DA | NZ6A-14C204-VA | €20 · Open |
| Ford Kuga2.0 250hp | Bosch MG1CS017 | — | — | NZ6A-14C204-VA | €20 · Open |
No file in this list matches. Search all original files →
About NZ6A-14C204-VA
NZ6A-14C204-VA is on 2 original (stock) ECU files in our catalogue: as the calibration on 2 files and as the SW upgrade number on 2 files.
They were read from Bosch MG1CS017 (2 files) control units.
Our catalogue lists them for the Ford Bronco (2.0 240hp) and Ford Kuga (2.0 250hp).
Other numbers on these files: 1 hardware number (M1PA-12B684-AA), listed on 1 of the 2 files; 1 software number (M1PA-12A650-DA), listed on 1 of the 2 files.
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- NZ6A-14C204-VA
- Files
- 2
- Found as
- calibration and SW upgrade number
- ECU types
- 1
- Vehicles
- 2
- Also written as
- NZ6A14C204VA · NZ6A 14C204 VA
ECU types with NZ6A-14C204-VA 1
Vehicles with NZ6A-14C204-VA 2
Tuning for Bosch MG1CS017 — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is NZ6A-14C204-VA listed for?
In our catalogue: Ford Bronco (2.0 240hp) and Ford Kuga (2.0 250hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has NZ6A-14C204-VA?
In our catalogue NZ6A-14C204-VA is on files read from Bosch MG1CS017 (2 files) control units.
There are several NZ6A-14C204-VA files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.