JR3A-14C204-BDJ original ECU files
2 original (stock) ECU files with the calibration JR3A-14C204-BDJ — Bosch MG1CS019, used in Ford vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All JR3A-14C204-BDJ files 2
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| Ford Mustang5.0 419hp · FSJK0 | Bosch MG1CS019 | — | — | JR3A-14C204-BDJ | €20 · Open |
| JL3A-12B684-CA JR3A-12A650-BBA Ford Mustang5.0 419hp · FSJK0 | Bosch MG1CS019 | JL3A-12B684-CA | JR3A-12A650-BBA | JR3A-14C204-BDJ | €20 · Open |
No file in this list matches. Search all original files →
About JR3A-14C204-BDJ
JR3A-14C204-BDJ is on 2 original (stock) ECU files in our catalogue: as the calibration on 2 files and as the SW upgrade number on 2 files.
They were read from Bosch MG1CS019 (2 files) control units.
Our catalogue lists them for the Ford Mustang (5.0 419hp).
Other numbers on these files: 1 hardware number (JL3A-12B684-CA), listed on 1 of the 2 files; 1 software number (JR3A-12A650-BBA), listed on 1 of the 2 files.
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- JR3A-14C204-BDJ
- Files
- 2
- Found as
- calibration and SW upgrade number
- ECU types
- 1
- Vehicles
- 1
- Also written as
- JR3A14C204BDJ · JR3A 14C204 BDJ
ECU types with JR3A-14C204-BDJ 1
Vehicles with JR3A-14C204-BDJ 1
Tuning for Bosch MG1CS019 — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is JR3A-14C204-BDJ listed for?
In our catalogue: Ford Mustang (5.0 419hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has JR3A-14C204-BDJ?
In our catalogue JR3A-14C204-BDJ is on files read from Bosch MG1CS019 (2 files) control units.
There are several JR3A-14C204-BDJ files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.