A123456789 original ECU files
18 original (stock) ECU files with the calibration A123456789 — Bosch MSE8.0, used in CF Moto, Zontes, Audi, Euro vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
ECU types with A123456789 1
Vehicles with A123456789 6
All A123456789 files 18
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| Audi A84.2 V8 340hp | Bosch MSE8.0 | B01A04120 | M346_G04 | A123456789 | €20 · Open |
| CF Moto Cforce40hp | Bosch MSE8.0 | B01A04120 | 8814KE15 | A123456789 | €20 · Open |
| CF Moto Cforce40hp | Bosch MSE8.0 | B01A04120 | 8814KS15 | A123456789 | €20 · Open |
| CF Moto Cforce40hp | Bosch MSE8.0 | B01A04120 | AJ1NC298 | A123456789 | €20 · Open |
| CF Moto Cforce40hp | Bosch MSE8.0 | B01A04120 | CDLCRFPR | A123456789 | €20 · Open |
| CF Moto Cforce40hp | Bosch MSE8.0 | B01A04120 | LJ125T-1 | A123456789 | €20 · Open |
| CF Moto Cforce40hp | Bosch MSE8.0 | B01A04120 | XB0205A5 | A123456789 | €20 · Open |
| CF Moto Papio125 9hp | Bosch MSE8.0 | B01A04120 | QJ350T02 | A123456789 | €20 · Open |
| CF Moto Uforce125 14hp | Bosch MSE8.0 | B01A04120 | — | A123456789 | €20 · Open |
| CF Moto Uforce125 14hp | Bosch MSE8.0 | B01A04120 | 8814LX12 | A123456789 | €20 · Open |
| CF Moto Uforce125 14hp | Bosch MSE8.0 | B01A04120 | 989NZF14 | A123456789 | €20 · Open |
| CF Moto Uforce125 14hp | Bosch MSE8.0 | B01A04120 | HSWN_NC2 | A123456789 | €20 · Open |
| Euro Falcon180 25hp | Bosch MSE8.0 | B01A04120 | 8814KS18 | A123456789 | €20 · Open |
| Zontes GK125 14hp | Bosch MSE8.0 | B01A04120 | 989LBY13 | A123456789 | €20 · Open |
| Zontes GK125 14hp | Bosch MSE8.0 | B01A04120 | I993_E05 | A123456789 | €20 · Open |
| Zontes GK125 14hp | Bosch MSE8.0 | B01A04120 | KWSNC450 | A123456789 | €20 · Open |
| Zontes GK125 14hp | Bosch MSE8.0 | B01A04120 | M827_G04 | A123456789 | €20 · Open |
| Zontes GK125 14hp | Bosch MSE8.0 | B01A04120 | QJ125T4V | A123456789 | €20 · Open |
Tuning for Bosch MSE8.0 — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Are these files modified?
No. Every file is an original (stock) read of a Bosch MSE8.0 control unit, delivered exactly as read. If you need a modified file, order tuning below.
How do I find the right file?
Read the ECU with your tool and compare the hardware (HW) and software (SW) numbers — and the calibration when several files share one software number. The vehicle name alone is not enough: the identifiers decide.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.
My number is not listed. What now?
Then we do not have this file: every original file we have is listed on this site and found by its search, so we cannot get it for you. Search one number at a time — HW, SW or calibration — exactly as it appears in your read.
Can you tune Bosch MSE8.0?
Yes. We make Stage 1/2 files and DPF, EGR, AdBlue/SCR and DTC solutions for Bosch MSE8.0 (depending on the engine). Upload your read on our file service.