10SW009438 original ECU files
4 original (stock) ECU files with the software number 10SW009438 — Bosch MEDC17.9, used in Jaguar vehicles. The other numbers (software, calibration) tell these files apart: compare them with your own read and open the matching file.
All 10SW009438 files 4
| Vehicle | ECU | HW | SW | Calibration / upgrade | |
|---|---|---|---|---|---|
| GX63-12K532-FAF Jaguar XE2.0 180hp | Bosch MEDC17.9 | — | 10SW009438 | GX63-12K532-FAF | €20 · Open |
| GX73-12K532-FHC Jaguar XE2.0 180hp | Bosch MEDC17.9 | — | 10SW009438 | GX73-12K532-FHC | €20 · Open |
| GX73-12K532-FKE Jaguar XE2.0 180hp | Bosch MEDC17.9 | — | 10SW009438 | GX73-12K532-FKE | €20 · Open |
| GX73-12K532-SAG Jaguar XE2.0 180hp | Bosch MEDC17.9 | — | 10SW009438 | GX73-12K532-SAG | €20 · Open |
No file in this list matches. Search all original files →
About 10SW009438
10SW009438 is on 4 original (stock) ECU files in our catalogue, always as the software number.
They were read from Bosch MEDC17.9 (4 files) control units.
Our catalogue lists them for the Jaguar XE (2.0 180hp).
Other numbers on these files: 4 calibration / SW upgrade numbers (GX63-12K532-FAF, GX73-12K532-FHC, GX73-12K532-FKE, GX73-12K532-SAG).
To choose, compare every number of your own read — HW, SW, calibration and SW upgrade where listed — with each file page before you buy.
- Number
- 10SW009438
- Files
- 4
- Found as
- software number
- ECU types
- 1
- Vehicles
- 1
ECU types with 10SW009438 1
Vehicles with 10SW009438 1
Tuning for Bosch MEDC17.9 — done by our engineers
- Stage 1 / Stage 2 / ECO
- DPF / FAP OFF
- EGR OFF
- AdBlue / SCR OFF
- DTC OFF
- Speed limiter, Start&Stop
Questions
Which vehicles is 10SW009438 listed for?
In our catalogue: Jaguar XE (2.0 180hp). Open the file page that matches your vehicle, engine and numbers.
Which ECU has 10SW009438?
In our catalogue 10SW009438 is on files read from Bosch MEDC17.9 (4 files) control units.
There are several 10SW009438 files. Which one do I need?
The one whose numbers match your own read: compare HW, SW, calibration and SW upgrade where they are listed on the file page. All sales are final, so check before you buy.
How do I get the file?
Open the file page and use Quick buy: €20 by card, no registration. We request the file from the original-file database and e-mail it to you — usually within minutes, normally within 24 hours. With an account on our file service fs.auto-remap.com you can also top up your balance and order there.
What exactly do I receive?
The original read only, as a ready-to-use .bin file (ordered through a file-service account: a ZIP archive with an .ori file inside). No full backups, EPROMs, SGO, VBF or other formats. Different tools expect different file sizes when writing, so make sure the file suits your device. All sales are final: check HW and SW against your own read before you buy.